Power cycle the printer by turning it off and on.Check for error codes and refer to the user manual.Ensure there are no paper jams or obstructions.Verify ink cartridges and paper trays are correctly installed.Perform a hard reset by unplugging and replugging the machine.If the issue persists, contact Riso customer support.
All questions need 'make model (what it is)'. We only have 'Scanner'. And then a clear question, what does 'scanner locked' mean? You are looking to lock it?
HP Support
https://support.hp.com > in-en > document
This message is displayed if the scanner is locked or the scanner module is not seated correctly. ... Enter a topic to search our knowledge library. Enter a topic .
..
They usually wrap around the rollers. It is better to turn the machine until it heats up as this softens the laminate plastic and makes removal easier. This was written for a larger desk model by the same applies. When I did mine I had to remove the top layers of laminate with a chef's boning knife.
There are two screws on the bottom which are visible. Leave them alone. The four screws that hold the bottom on are UNDER the rubber feet. Gently lift one edge of the rubber feet and then carefully peel them off. You will need a long thin Phillips screw driver to remove the four screws, UNPLUG the unit before opening it.
In most cases the plastic will be wrapped around the orange/red heated ceramic roller. This roller cannot be turned unless you push the "Release" lever. Using a tweezers, try to grasp a corner of the end of the rolled up plastic. Pull firmly and steadily on the corner until you have enough free to grasp with a needle nose pliers or a forceps, Then work your way across the entire end of the plastic sheet until its free. Finally, reposition the pliers or forceps toward the middle of the freed end and firmly pull to unroll completely.
Remember, you must be pushing on the "Release" while doing this or the roller will not turn. When you start, you may have to move the roller to get it to a position where you can try to grab an end corner of the plastic sheet. You should be able to do this if you a pushing on the Release lever.
Finally, if you have left the rolled up plastic sheets on the roller so long the are fused into one mass, my directions my not work. In that case, try slitting the entire length of the rolled up plastic with something like an xacto knife, BUT DON'T CUT THE RUBBER ROLLER. That's tricky, but at this point you have nothing to lose.
Took me 20 minutes to figure out how to open the unit. Ten minutes to take out the wrapped up plastic sheets.
..
HelloYou haven't specified anything about your projector or other detalis about it. jsut get into this link, and see whether the lamp you want is available there or not. You have to search with its number. It will have a model number on it. OKhttp://www.visualapex.com/accessories/lamp-projection-tv.asp?MFR=DNGO
We only speak English on Fixya. We are a North American website and only speak English.
Even translated, it doesn't make sense.
FULL 'make model (what is is)' fist 3 words, plus QUESTION please.
https://translate.google.ca/?sl=auto&tl=en&op=translate
..
Let's start by setting up the binary columns.
2^0 = 1
2^1 = 2
2^2 = 4
2^3 = 8
2^4 = 16
2^5 = 32
2^6 = 64
2^7 = 128
Written horizontally.
128 64 32 16 8 4 2 1
1 1 1 1 1 1 1
What is the biggest number that goes into 127. 64. Put 1 in the 64s column. 127 - 64 = 63.
What is the biggest number that goes into 63. 32. Put 1 in the 32s column. 63 - 32 = 31.
What is the biggest number that goes into 31. 16. Put 1 in the 16s column. 32 - 16 = 15.
What is the biggest number that goes into 15. 8. Put 1 in the 8s column. 15 - 8 = 7.
What is the biggest number that goes into 7. 4. Put 1 in the 4s column. 7 - 4 = 3.
What is the biggest number that goes into 3. 2. Put 1 in the 2s column. 3 - 2 = 1.
Put a 1 in the 1s column.
So we have 1111111 in binary.
Good luck.
Paul
printer P510k by HITI sold 2008 first one
HiTi P510K Digital Photo Kiosk Printer<< real name
No error told, at all,
No country told. (not sold USA ) we are N.American, web site.
google finds this in seconds
see chapter 8 ,errors
http://edis.hiti.com/DISUpload/Upload/distributor/technicalupdate/P510K%20Service%20Guide%20v1.5.pdf
the book says some error you must ask them for support (TBD ) marked
I say ask them, for help.
Question edited for a lot more clarity.
GE ENERGY STAR 24.7 Cu. Ft. French-Door Refrigerator.
In reality, your new fridge is purchased to fit the space you have.
..
Scribd
https://fr.scribd.com > doc > RISO-EZ-200
RISO EZ 200 P96-569 = Either The Print Drum Color Information or Ink Category Information Is Still Not Input And D04-560 = Ink Tag Is Not Detected On Ink .
..
You can find the drivers and utilities that you need for your office equipment and supplies in this link:
Drivers & utilities ' Toshiba Tec Europe. Just click on the link provided and it will direct you to the page or website. Thank you!
