Remote control code

The remote control for your DVR has the capability to control 2 additional DVRs in addition to the one that you currently have. In order for the remote control to work with your DVR, you will need to make certain both of them are talking on the same frequency. If you press the remote control and the front of your unit says DR2, that means that you need to have your remote on DR2 as well so that it can operate the DVR. To set your remote to DR2, you will need to make sure the unit is off then you will need to press and hold down the SETUP button and while you are holding this button down, press the number 2 button. Your remote is now set to DR2.

Good luck...

Press the setup button until the light blinks twice and then enter the code associated with your material.

Dear Sir/madam,

The most important remote code, of course, that could be gleaned from all this is the discrete off (play could be used for discrete on):

- Discrete off: 900A 006D 0000 0001 45B5 936C

- Edit... Discrete on? 900A 006D 0000 0001 45B5 FE01

But I also found some interesting maintenance codes in the Cxxx range. Trying this though, I'd recommend being very careful and avoiding e.g. the code ending with xx3A. That starts some kind of update process apparently saying don't shut down. It accepts no remote commands (it shows the remote code pressed on player's screen though, which is interesting), no powerdown but is fortunately exitable by pressing Eject on the player - or at least was for me, I'm not trying that one again... Whew. Some other codes also produce error messages on video or on player screen.

These codes I found to do something interesting:

- Player display test, all the items in the player display light up and animate: 900A 006D 0000 0001 45B5 C738

- Disc tray lock (for all you folks with kids) on and off: 900A 006D 0000 0001 45B5 C639

- Time and date on players screen (sorry, only for a moment): 900A 006D 0000 0001 45B5 CB34

- Factory reset (you loose all your settings): 900A 006D 0000 0001 45B5 CD32

---

- Time and date on players screen (sorry, only for a moment): 900A 006D 0000 0001 45B5 CB34

- Factory reset (you loose all your settings): 900A 006D 0000 0001 45B5 CD32

Try to Factory Reset with your remote


For more details click this link.....

http://www.avsforum.com/avs-vb/showthread.php?t=940909


thanks
good luck

Http://www.hifi-remote.com/ofa/codes-tv.shtml#tv

If none of the codes work then we have two other solutions:

1. Searching For Your Code

If you have tried all of the set-up codes for your brand of equipment ,or yourbrand is not listed, and you are still not able to get the unit to respond, trythe following procedure to search for your code.
If you don't find a code that works, the remote will flash four times when youreach the end of all the codes for this device type.

1. PRESS the button for the device you want to program, (TV, VCR, CABLE, etc.), then RELEASE.
2. PRESS and HOLD the SETUP button until the red LED flashes twice, then RELEASE.
3. ENTER 9-9-1 (two blinks on the remote)
4. ALTERNATE slowly between the POWER key and the DEVICE (TV, VCR, CABLE, etc.) button until your device turns off. (On VCR, LD, and CD players use PLAY instead of POWER)
   Make sure that the remote is pointed at your device during the search, You may have to press this sequences of buttons up to 100 times to search the entire library of codes.
5. When your device turns OFF, PRESS the SETUP button and RELEASE it to lock in the code for your device.

1. PRESS and HOLD the SETUP button until the red LED flashes twice.
2. PRESS 9 - 7 - 5, the red LED will flash twice.
3. PRESS the DEVICE key where you wish to learn the function. The next 3 steps must be completed within 10 seconds.
4. PRESS the button that will receive the learned function, the LED will flash rapidly.
5. PRESS the button on the original remote to be learned.

Holding the STOP button for some time may solve your problem.

Hi,
Refer to the owners manual, and reconfigure the device. The following is the link for the onwers manual.

http://www.tacp.toshiba.com/tacpassets-images/models/RD-XS35/docs/RD-XS35_om_e.pdf



Thanks
proton

Hi

First of all try soft reset, both HDD recorder and remote control, Unplug the HDD recorder and keep unplugged about 2-3 minutes. Take the batteries of remote control out and put it back 30 seconds later (Make sure batteries are OK)