Panel2 function description - Matsonic MS9158E+ Motherboard

Who replaced the headlamp bulb ? Take it back . Everything your having problems with are all controlled by the BCM - body control module . May have crossed wire's ,shorted etc....
This vehicles BCM functions as the Power Mode Master (PMM). Refer to Power Mode Description and Operation for a complete description of the power mode functions.
Body Control Module
The various body control module (BCM) input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The BCM functions include the following:
• Battery rundown protection--Inadvertent power--Refer to Interior Lighting Systems Description and Operation .
• BTSI/automatic transmission shift lock control--Refer to Automatic Transmission Shift Lock Control Description and Operation .
• Bulb check--Refer to Instrument Cluster Description and Operation .
• Chimes--Refer to Audible Warnings Description and Operation .
- Check gages
- Content theft deterrent
- Door ajar warning
- Headlamps ON
- Key-in-ignition
- Oil reset
- Park brake warning
- Seat belt not fastened
- Turn signal ON
- Vehicle theft deterrent
• Door lock interface--Refer to Power Door Locks Description and Operation .
• Exterior and interior lighting control--Refer to Exterior Lighting Systems Description and Operation .
- Automatic lighting control
- Backup lamps
- Daytime running lights (DRL)
- Fog lamps
- High/low beam head lamps
- Park brake lights
- Turn hazard lamps
• Gage control--Refer to Instrument Cluster Description and Operation .
• Heated seats--Refer to Heated Seats Description and Operation .
• Horn interface--Refer to Horns System Description and Operation .
• Instrument cluster indicator control--Refer to Instrument Cluster Description and Operation .
• Interior lighting--Refer to Interior Lighting Systems Description and Operation .
• Key-in-ignition sensing--Refer to Audible Warnings Description and Operation .
• Parking brake state sensing--Refer to Brake Warning System Description and Operation .
• Retained accessory power (RAP)--Refer to Retained Accessory Power (RAP) Description and Operation .
• Rear compartment interface--Refer to Power Door Locks Description and Operation .
• Rear defogger--Refer to Rear Window Defogger Description and Operation .
• Remote function control--Refer to Keyless Entry System Description and Operation .
• RFA communication link--Refer to Keyless Entry System Description and Operation .
• Seat belt use sensing--Refer to Seat Belt System Description and Operation .
• Theft deterrent vehicle/content--Refer to Content Theft Deterrent (CTD) Description and Operation or Immobilizer Description and Operation .
• Washer solvent level sensing--Refer to Wiper/Washer System Description and Operation .
• Wiper/washer--Refer to Wiper/Washer System Description and Operation .

Door ajar switch problem more then likely or wiring issue . The BCM - body control module won't turn off interior light , let door lock because it think's the door is open . The door ajar switch is a input to the BCM .

The first thing would be to have it checked for DTC'S - diagnostic trouble codes . Also check with an enhanced scan tool to see if the BCM shows ajar switch data (open or closed ? Do you know about body electronics ?
Body Control Module
The various BCM input and output circuits are described in the corresponding functional areas indicated on the BCM electrical schematics. The Body Control Module functions include the following:
?€¢
A/C compressor request. Refer to Air Temperature Description and Operation

?€¢
Remote Function Control. Refer to Keyless Entry System Description and Operation

?€¢
A/C cooling Fan. Refer to Air Delivery Description and Operation

?€¢
Audio Delay Power. Refer to Radio/Audio System Description and Operation

?€¢
Exterior and interior lighting control. Refer to Exterior Lighting Systems Description and Operation

-
Daytime running lights (DRL)

-
Automatic lighting control

-
Fog lamps

?€¢
Interior lighting. Refer to Interior Lighting Systems Description and Operation

?€¢
Battery rundown protection (Inadvertent Power). Refer to Interior Lighting Systems Description and Operation

?€¢
Chimes. Refer to Audible Warnings Description and Operation

-
Key-In-Ignition

-
Head Lamps On

-
Seat Belt Not Fastened

-
Turn Signal On

-
Park Brake Warning

-
Door Ajar Warning

-
Check gages

?€¢
Gage control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Instrument cluster indicator control. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Theft deterrent. Refer to Theft Systems Description and Operation .

?€¢
Engine coolant level sensing. Refer to Cooling System Description and Operation .

?€¢
Washer solvent level sensing. Refer to Wiper/Washer System Description and Operation in Wipers/Washer Systems.

?€¢
Key-in-ignition sensing. Refer to Audible Warnings Description and Operation in Instrument Panel, Gages, and Console.

?€¢
Seat belt use sensing. Refer to Seat Belt System Description and Operation .

?€¢
Brake fluid level sensing.

?€¢
Parking brake state sensing.

?€¢
Rear compartment interface. Refer to Power Door Locks Description and Operation

?€¢
Horn interface.

?€¢
Door lock interface. Refer to Power Door Locks Description and Operation

?€¢
Bulb Check. Refer to Instrument Cluster Description and Operation in Instrument Panel, Gages, and Console.

what keys do you need descriptions for? if you're talking about the function keys (F1, F2, etc), they have different functions in different applications. what program are you looking for?

Did you mean the microphone or internal speaker in your laptop?
1. open control panel
2. open sound
3. under playback cofigure speaker levels.
4. under recording configure microphone.
5. apply then OK and in all windows.
Hope this helps

1-Control panel
2-Security
3-Firewall

at the left of your screen you will see Turn windows Fwall on /off.

DO these Series of steps:
1. control panel2. hardware and sound3. then under Devices and printer you gonna see Device Manager4.click on it5. look for your touch pad and enable it.
if this does not work then go to manufacturers website and download the driver for your touch pad.
Hope this was helpful : )

Well ill assume ur talking about connecting to the internet, this way:
1.Control Panel2.Network and Internet3.Network and Sharing Center4.Set up a connection or network5.Connect to the Internet.
If this is not what ur talking about then please comment to clarify

do this:
1. Control Panel2.Network and internet3.Network and Sharing center4.connect to a network5.click on the the network u wish to connect to6.type in pass-phrase if u have one otherwise you'll be connected
hope this help, and if it does not then just reply back in the comments,good luck = )

Do you have a proxy setup?
In Windows...
1. Control Panel
2. Internet Options
3. Connections tab
4. Lan settings button

Do you have a proxy setup here? If so remove it.

Restart your computer if you haven't already.

Hope this helps!

pal go to "driver guide"sing up free and go to browes-bios\motherboard-choose"matsonic"-enter "ms9158e+" then you well have manuall downloode it run it on acrobart(adobe)