Boss BV7200 Car DVD Player - Page 4 - Answered Questions & Fixed issues
Why does my boss 1600 watt diablo amp cut off at high volumes
Chances are your speakers are running at to low of impedance. Check if your running aftermarket. speakers, if so they are probably wired in parralle. Change the wiring to "series"increasingly your impedance from 2ohms to 8, that should solve your issue.
What is the deal with the green parking brake wire on the boss 7320?
By U.S.federal law you can't drive and have a movie playing at the same time, that wire when connected will only let you watch the movies while the vehicle is in park. To go around this all you have to do is ground the wire, I always just ground them the the radio itself on the backside around a bolt on the radio heat sink, and there you go you now can drive and watch Movies.
Boss AR4000D 4000W MONO Car Amplifier owners manual
here you go man.
sorry you bought this amp. I hope it does what you want it to, I am pretty sure it will never do what they say it will but It may do what you want it to for the price.
here is the manual you asked for. http://bossaudio.com/manual/ARMOR_D_EN_UM.PDF
Hi i just installed a boss am/fm receiver in my boat it works for about five minutes then start to turn on and off, on and off. any suggestion.
I'm not experienced with the boss, BUT..... the symptom suggests that you have wired the receiver into a circuit which:
1. has too low a curent rating [not enough amps] for the receiver device, AND....
2. is protected with a SELF RESETTING circuit breaker.
IF that is the situation, then the OVERLOAD caused by the too heavy receiver is causing the circuit breaker to "TRIP" and cut off the electric power in the circuit.
Self resetting breakers work by having a bi-metallic strip inside which causes the strip, when overheated by an overload, and in bending, OPEN the circuit, cutting off the power. This reduces the risk of an electrical fire!!!!!
When the bi-metallic strip cools enough, it RE-CLOSES the circuit, turning the power back on UNTIL the overload causes to to trip again.
This is a safety/fire protection issue, AND you need to take your vehicle to a QUALIFIED [CERTIFIED preferably] vehicle sound shop where a qualified TECHNICIAN can troubleshoot the issue, and probably will either find a more powerful supply circuit, OR....
ADD a new, adequately sized wiring circuit to support your sound equipment.
What this issue sounds like is that YOU have installed a sound system/device which needs MORE POWER than your existing circuit can safely provide!!!!!!!!
Be SAFE, get PROFESSIONAL HELP!!!!
Bv 9962
If you wish to get some details; check the site linked here. Viewing it in "
Mosaic" or "
Magazine" will make surf easy. Pull up older posts. Surf the site with patience.
Do a search by type in the brand name of your device at its search box and press "Enter".
http://electronicshelponline.blogspot.com/
Amp going into protect mode
The first thing I would check is how your speakers are wired to the amp. Multiple speakers wired in series or parallel will change the overall impedance that the amplifier "sees". If your impedance is too low (let's say 1 ohm) and your amp is only stable to 2 ohms, the amp will shut off to prevent over heating and damage. Hope this helps.
Stays on white screen
Sorry to tell u, but ur screen went out.. That brand will only last so long. Maybe a loose wire somewhere, but from what I've read, it is just overblown.
JUST NEED WIRING DIAGRAM FOR PH5000D BOSS FOR TWO SUB
When two sub woofers are wired the most important thing that must be remembered is to keep the polarity and PHASING to be in line within the space.The sub can be connected in Series or in Parallel ( if the amplifier takes in very low impedance).The connections can be bridged from the output.Finally your taste to listen must determine the final settings and response
I had my boss 2400
If your amp started smoking, probably not. Due to your description, did the other sub really blow? I would hook it up to another amp to test it. It may have been a channel in your amp. As for repairing the amp, the parts and labor to repair will probably cost you more that to just replace the amp.
How to connect an boss
Assuming you have an aftermarket radio. You must remove the radio so you can attache your RCA cables and the remote turn on. Run these down one side of the vehicle back to the amplifier. Run the power wire from the battery back down the other side of the vehicle to the amplifer (remember to place your fuse within 12 inches from the battery connection. You will need to find a grounding point. I recommend removing one of the side carpeted panels to do this. You will be able to find the frame. Make sure to sand around where you will be connecting the ground. Hook wires to the amp (RCA to correct color RCA wire inputs, Ground wire to (-), power wire to (+), and remote wire to it's screw terminal. The other end of the amplifier should have the speaker outputs for your subwoofer(s). Hope this helps. If you need more information visit
www.mobileinformationlabs.com
I have a car estereo
Try to make sure the red wire is going to a switched power source. That is, a source that is off when the key is off.
Not finding what you are looking for?
